bucking strength中文是什么意思

• 浸渍强度；弯曲强度

• "buck"中文翻译    n. 巴克〔姓氏〕。
• "strength"中文翻译    n. 1.力，力量，体力。 2.强度，浓度；长处；(要塞 ...
• "bucking" 中文翻译 :    比金; 锤碎; 地壳弯曲; 地曲; 二次爆破; 反冲的; 反抗的; 反作用的; 浸渍, 浸润; 浸渍；浸润; 破冰前进; 人工磨矿; 弯曲，弯折; 造材
• "bucking bar" 中文翻译 :    打钉杆; 铆钉顶棒
• "bucking board" 中文翻译 :    研磨盘
• "bucking brace" 中文翻译 :    补偿拉条
• "bucking bronco" 中文翻译 :    难驯的马
• "bucking circuit" 中文翻译 :    抵消电路
• "bucking coil" 中文翻译 :    补偿线圈; 反感线圈; 反感应线圈
• "bucking current" 中文翻译 :    屏蔽电流
• "bucking effect" 中文翻译 :    反电动势效应
• "bucking electrode" 中文翻译 :    屏蔽电极
• "bucking electrodes" 中文翻译 :    屏蔽电极
• "bucking factor" 中文翻译 :    扭曲系数
• "bucking field" 中文翻译 :    反向场
• "bucking hammer" 中文翻译 :    矿石打碎锤; 碎矿锤
• "bucking kier" 中文翻译 :    煮练锅
• "bucking ladder" 中文翻译 :    梯形造材台; 梯状造材垫木
• "bucking load" 中文翻译 :    压曲临界荷载, 折断载荷
• "bucking plate" 中文翻译 :    炉子配件钢板
• "bucking potential" 中文翻译 :    补偿电压
• "bucking saw" 中文翻译 :    造材锯
• "bucking stress" 中文翻译 :    弯折应力
• "bucking the tongs" 中文翻译 :    铺设螺纹管线的铺管队；用管钳接管; 用管钳接管
• "bucking transformator" 中文翻译 :    反作用变压器

• This thesis used along caldwell ' s direct calculation method of the ultimate strength of ship hull girders , considered the double bottom and upperwing tank to ship ultimate strength contribution , first defined the stress distribution of the whole section of the ship girders . that is : in the sagging condition , deck and side shell of nearby deck remain the ultimate bucking strength , double bottom remain the yield stress . and the other parts keep elasticity
  本文沿用caldwell等人直接计算船体极限强度的思想，考虑双层底和顶边水舱对船体极限强度的贡献，首先将船体梁整体破坏时剖面应力分布确定为：在中垂状态下，甲板及甲板附近的舷侧均屈曲，双层底区域则均屈服，其他部分保持弹性状态；在中拱状态下，双层底及之间的底舷侧均屈曲，甲板及顶边水舱区域均屈服，其他部分则保持弹性状态。
• In the hogging condition , double bottom and the side shell remain the ultimate bucking strength , deck and upperwing tank remain the yield stress , and the other parts keep elasticity . then the key to calculate the ultimate strength of ship hull girders is to ascertain the ultimate bucking strength of the stiffened panels . in this regard , the developed formulation is designed to be more sophisticated than previous simplified theoretical method for calculating the ultimate strength of stiffened panels under combined in - plane bending and lateral pressure . fabricatio n - related initial imperfections ( initial deflections and residual stresses ) are included in the panel ultimate strength calculation as parameters of influence . all possible collapse modes involed in collapse of stiffened panels , including overall buckling collapse , column or beam - column type collapse , tripping of stiffeners and local bukling of stiffened web are considered
  确定了船体梁整体破坏时的剖面应力分布之后，关键在于确定板架的极限屈曲强度。本文充分考虑了在纵向弯曲、横向压力作用下加筋板可能发生的几种破坏模式，即板架的整体屈曲破坏、梁柱形式的破坏、筋的侧倾、腹板的屈曲并同时考虑了初始焊接残余应力、初挠度的影响，使其更精确的计算加筋板的屈曲强度。对于加筋板中加强筋腹板的局部屈曲，采用解析法推导出筋的腹板的挠度方程及其边界条件，求解相应的方程，从而计算出腹板的局部屈曲应力。